P01CE code meaning
Cylinder 2 Injection Timing Performance - Over Advanced
Powertrain system Generic code P01xx codes Check engine light
What P01CE means
Diesel engines must detect when fuel can no longer be injected at the correct crank angle – CARB requires this for every injector individually, hence one code per cylinder. The start of injection is not measured directly: during overrun with fuel cut-off the control module fires a tiny test injection into one cylinder (GM: about 1.5 mm³) and evaluates the resulting speed change at the crankshaft sensor. From this it learns how much extra energizing time the injector needs (Bosch calls this zero fuel calibration). This code means injector 2 needs clearly less energizing time than intended, i.e. it opens too early or delivers too much – GM sets it below −90 µs, after two trips. Documented users are GM's 6.6 litre Duramax (LML, L5P) and FCA's 3.0 litre EcoDiesel; Ford reports the same function under P2B11ff. Bulletins often point away from the injector: GM fixed false settings on 2020–2021 L5P trucks with new software and warns that vibration, for example from off-road tires, disturbs the evaluation; FCA lists wrong injector correction codes, boost leaks and loose injector clamps.
P01CE at a glance
- Check engine lightYes, usually on
- Emissions testCan fail
- Limp modeNot expected
- Repair difficultyHard
- Typical labor0.5 to 4 hours
- Clears after repairAfter a drive cycle
Symptoms of P01CE
- Check engine light on (after two drive cycles)
- Louder combustion noise or knocking
- Rough idle
- Possibly smoke
Common causes of P01CE
- Most likelyInjector worn or leaking (delivers too much in small quantities)
- PossibleFalse setting from software or vehicle vibration (e.g. off-road tires)
- PossibleWrong injector correction code stored after an injector replacement
- Less likelyBoost leak or loose injector clamp
- Less likelyContaminated fuel
Check the most likely causes first. Replacing parts by guesswork is the most expensive way to clear a code.
Parts involved
Fuel injector cylinder 2Crankshaft position sensorEngine control module
What each part of P01CE means
| P | Powertrain system: engine, fuel system, ignition, emissions and transmission. |
| 0 | Generic code: it means the same on every make (SAE standard). |
| 1 | Area: fuel and air metering. |
| CE | The exact fault in that area. |
What to do next
- Note P01CE and any other codes stored with it: several codes together often point to one cause.
- Check for loose connectors and damaged wiring around the parts the code names.
- Check open recalls for your car: some faults are fixed for free by the dealer. Enter your VIN.
- Clear the code only after the repair. If it comes back, the fault is still there.
Buying a used car? Scan it for stored codes before you pay. A recently cleared memory can hide a problem.
Questions about P01CE
What does P01CE mean?
P01CE means "Cylinder 2 Injection Timing Performance - Over Advanced". Diesel engines must detect when fuel can no longer be injected at the correct crank angle – CARB requires this for every injector individually, hence one code per cylinder. It is a generic code, so it means the same on every make.
Is it safe to drive with P01CE?
Usually yes, for a short time, if the check engine light is steady and the car drives normally. If the light flashes or the car runs badly, stop and have it checked.
Will P01CE fail an emissions test?
Yes, it can. P01CE is emissions-related, so most inspection programs fail a car while it is stored or while the check engine light is on.
How hard is P01CE to fix?
Difficulty: hard. A typical repair takes 0.5 to 4 hours of work. This is a job for a workshop.
Will P01CE clear itself after the repair?
After the repair the car has to complete a drive cycle (a mix of city and highway driving) before the test runs again. Until then the readiness monitor shows "not ready", which can fail an inspection.