P07F6 code meaning
Gear 9 Incorrect Ratio
Powertrain system Generic code P07xx codes Check engine light
What P07F6 means
A ratio code compares input or turbine speed divided by output speed with the ratio of the commanded gear; a slipping clutch or the wrong gear trips it. Ford's summaries describe the check (over 30 rpm off for more than 1.8 s, three times) for gears 1–6 only; its 10-speed bulletins show gears 7–10 as P076F, P07D9, P07F6 and P07F7. P07F6 covers 9th gear. Ford's 10R80 bulletins from 2023 to 2025 (F-150, Mustang, Ranger, Explorer, Transit, Expedition) list it with the other ratio codes; the causes are adaptive learning, the valve body and a migrating clutch cylinder sleeve. The 10R140 bulletin of 2021 does not mention it. Nissan's nine-speed Frontier and Titan set it with the MIL on; the repair check drives each gear 1–9 for at least 10 s in manual mode.
P07F6 at a glance
- Check engine lightYes, usually on
- Emissions testCan fail
- Limp modePossible
- Repair difficultyHard
- Typical labor0.5 to 14 hours
- Clears after repairWhen cleared with a scanner
Symptoms of P07F6
- Slipping or flaring engine speed in gear 9
- Harsh or delayed shifts
- Check engine or transmission warning lamp
- Gear 9 locked out, higher rpm at cruise
Common causes of P07F6
- Most likelyClutch slipping or hydraulic leak (Ford 10R: migrating sleeve in the CDF clutch cylinder)
- Most likelyShift adaptives wrong or not learned
- PossibleSticking valve in the valve body
- PossibleFluid level low or fluid degraded
- Less likelyTurbine or output speed sensor signal wrong
Check the most likely causes first. Replacing parts by guesswork is the most expensive way to clear a code.
Parts involved
Transmission clutchesTransmission valve bodyTransmission fluidTransmission control module
What each part of P07F6 means
| P | Powertrain system: engine, fuel system, ignition, emissions and transmission. |
| 0 | Generic code: it means the same on every make (SAE standard). |
| 7 | Area: transmission. |
| F6 | The exact fault in that area. |
What to do next
- Note P07F6 and any other codes stored with it: several codes together often point to one cause.
- Check for loose connectors and damaged wiring around the parts the code names.
- Check open recalls for your car: some faults are fixed for free by the dealer. Enter your VIN.
- Clear the code only after the repair. If it comes back, the fault is still there.
Buying a used car? Scan it for stored codes before you pay. A recently cleared memory can hide a problem.
Questions about P07F6
What does P07F6 mean?
P07F6 means "Gear 9 Incorrect Ratio". A ratio code compares input or turbine speed divided by output speed with the ratio of the commanded gear; a slipping clutch or the wrong gear trips it. It is a generic code, so it means the same on every make.
Is it safe to drive with P07F6?
Drive gently and only to a workshop. With P07F6 the car can go into limp mode (reduced power) to protect itself.
Will P07F6 fail an emissions test?
Yes, it can. P07F6 is emissions-related, so most inspection programs fail a car while it is stored or while the check engine light is on.
How hard is P07F6 to fix?
Difficulty: hard. A typical repair takes 0.5 to 14 hours of work. This is a job for a workshop.
Will P07F6 clear itself after the repair?
Clear the code with a scanner after the repair. If the fault is fixed, it does not come back.